- #Wd my passport is too slow mod
- #Wd my passport is too slow Patch
- #Wd my passport is too slow professional
- #Wd my passport is too slow zip
What happened to me constantly is that there was nothing on it that I had copied at that moment. Via the app you can look, with only an active WiFi connection, what is written on the WD card.
Each light represents a percentage of about a quarter override. The SD card is inserted into the WD and the lights above begin to blink 1 by 1 until all 4 lights emit a steady blue light. The phone or other product can connect, but this can also be done later. Wait until the blue lights stop flashing and the wifi continues to show a blue color (in the previous one, all lights flashed constantly as a signal of a defect). With the app and the WiFi connected, the files can be read which are transferred to the My passport via the SD card. The WD Mypassport provides a WiFi signal to which you can connect your phone or other electronic product. I quickly tested the device and installed the app. Last-Minute bought a new one at Coolblue which was delivered the same evening. I had bought a second-hand one from a competitor, which eventually turned out to be defective. If it makes a pattern with skip runs then weak head, if runaway skipping causes skip resets then it is some other problem.ĮDIT: Have you checked the smart data? The smart data might give an indication as to the health of the drive.Unclear via app whether transfer was successful
#Wd my passport is too slow zip
If you are not sure and you are allowed to attach files then zip the files and attach it to your next post.Īre you getting any read errors, or is it just slow reading? Does it look like it reads in bursts? You could import the ddrescue recovery into HDDSuperClone and see if it induces the skipping algorithm.
#Wd my passport is too slow mod
You could dump mod 02 again and compare it to the before and after and it should match the after (patched). If you used HDDSuperTool to apply the patches then you should have the before and after bin files.
#Wd my passport is too slow Patch
The slow fix patch only modifies a single byte in mod 02, and a specific section of mod 32. If you play with modules without knowing what you are doing you might as well kiss your data goodbye.
#Wd my passport is too slow professional
I am not sure exactly what would happen if you zeroed the whole module, but you could very likely lock yourself out of the drive in which case only a professional with proper tools could write the module back again. If I keep a backup of the module, is there a risk here to damage the drive or contents if I zero out the module?ĭO NOT WRITE ALL ZEROS TO MOD 02! That post was an experiment that just happened to work because it overwrote the byte that performs the slow fix to mod 02. Drive CPU/RAM, ROM are ok, but Translator and Defect Lists only have partial access.Īny ideas what could be the issue? Does it have something to do with the encryption from the JMS chip? What would be the next step here to recover data?īasically I'm only copying at like 800 kB/s currently and it's going to take me like 15 days to ddrescue this drive. Rapidspar says the heads are 100% healthy and 79% of tested sectors contain data. It also reads incredibly slow ddrescue was reading at like 320kb/s. The drive is now recognized as a 1TB WD drive, but Windows/Linux/Mac/Rapidspar do not see a partition map. I left them on and soldered on the A and B wires from the SATA port to the other end of the caps that would normally go to the JMS chip. I removed U14, then desoldered C13, C18, C31, C37 from the JMS side as it said in the thread, but what wasn't clear was whether to leave the caps on or not. I followed this guide here: viewtopic.php?f=1&t=27819 It seemed to spin up fine and I didn't hear any clicking. The LED would flash a few times, then go steady, then flash again. I have a WD My Passport Ultra 1TB with a 2060-771961-001 PCB that wasn't being recognized by the computer at all.
0 kommentar(er)
